Constitutive modelling and numerical simulation of multivariant phase transformation in superelastic shape‐memory alloys

This work concerns the micromechanical constitutive modelling, algorithmic implementation and numerical simulation of polycrystalline superelastic alloys under multiaxial loading. The model is formulated in finite deformations and incorporates the effect of texture. The numerical implementation is based on the constrained minimization of the Helmholtz free energy with dissipation. Simulations are conducted for thin tubes of Nitinol under tension–torsion, as well as for a simplified model of a biomedical stent. Copyright © 2004 John Wiley & Sons, Ltd.     

The Influence of Surfactant on the Surface Characterization of Celestite in Spherical Oil Agglomeration

This study investigates the relationship between the critical surface tension of wetting of celestite and agglomeration recovery as well as the zeta potential in dependence of pH and amount of collector (Na‐Oleate). For this purpose, effects of pH and collector amount on the agglomeration recovery are investigated and zeta potential measurements and Fourier Transform Infrared Spectrophotometer (FTIR) analyses are carried out to determine the adsorption type of Na‐Oleate on celestite surface. The sessile drop technique is used for the measurement of contact angle and determination of the critical surface tension of wetting (Y_C) of celestite. The maximum agglomeration recovery is obtained at pH 7. The critical surface tension of wetting of celestite is very close to the surface tension of kerosene, which is 25.95 mN/m. Furthermore, at the optimum Na‐Oleate amount of 10 kg/ton, the critical surface tension of wetting of celestite is approximately equal to the surface tension of kerosene.     

单层多跨刚架在移动荷载作用下的影响量计算方法

讨论了桥梁、工业厂房和大型公共建筑中较多采用的单层多跨刚架在移动荷载作用下影响量的计算方法。以工程中计算连续梁的一次力矩分配法的概念和思路为基础,建立了结构中杆端真实抗转刚度和结点转角传递的概念及其相应计算公式,提出了一种单层多跨刚架超静定结构影响量的精确计算方法。算例表明,该方法较之传统的计算方法简捷,且既便于手算,也利于编制通用程序用于电算。     

Pool boiling on a superhydrophilic surface

Titanium Dioxide, TiO₂, is a photocatalyst with a unique characteristic. A surface coated with TiO₂ exhibits an extremely high affinity for water when exposed to UV light and the contact angle decreases nearly to zero. Inversely, the contact angle increases when the surface is shielded from UV. This superhydrophilic nature gives a self-cleaning effect to the coated surface and has already been applied to some construction materials, car coatings and so on. We applied this property to the enhancement of boiling heat transfer. An experiment involving the pool boiling of pure water has been performed to make clear the effect of high wettability on heat transfer characteristics. The heat transfer surface is a vertical copper cylinder of 17 mm in diameter and the measurement has been done at saturated temperature and in a steady state. Both TiO₂-coated and non-coated surfaces were used for comparison. In the case of the TiO₂-coated surface, it is exposed to UV light for a few hours before experiment and it is found that the maximum heat flux (CHF) is about two times larger than that of the uncoated surface. The temperature at minimum heat flux (MHF) for the superhydrophilic surface is higher by 100 K than that for the normal one. The superhydrophilic surface can be an ideal heat transfer surface. Copyright © 2002 John Wiley & Sons, Ltd.     

试论双点后方交会简便公式

根据双点后方交会的图形特点和已知条件，列出了方程组，推导出了双点后方交会直接计算座标的简便公式，同时求出了精度计算公式，以供测量人员参考     

井巷掘进控制斜形炮孔钻孔精度的试验研究

井巷掘进爆破工程中，工作面按设计要求，布置各种斜形炮孔，利用量角器和垂直尺控制钎杆与工作面夹角，使炮孔钻孔精度与设计炮孔角度基本上符合，在生产中取得了良好的爆破效果．     

Determination of the width of the transition layer between the crystalline and amorphous zones in nylon 1010 by SAXS

The width of the transition layer between the crystalline and amorphous zones in nylon 1010 was determined by SAXS with point collimation and long-slit collimation, respectively. The width of the transition layer, E, was found to be 1.7 nm. The results show that the width of the transition layer is independent of crystallinity.     

掺气减蚀设施水力计算的改进

结合小湾工程泄洪洞模型试验进行了11种挑跌坎型和6级流量的试验观测，据此提出了特别适用于大单流量条件的射流出射角修正式，提出了射流近底流速的选取原则.与实验资料对比证明本文计算方法有足够精度。     

套管固井质量问题及对策分析

从油田现场反应的情况出发，对调整井固井，尾管固井，大位移井套管固井和其他固井的质量问题进行了分析，针对各种问题产生的原因，提出了相应换解决办法。     

正交异性材料在R.Hill屈服准则下平面应力问题的特征场(h>2)

大多数金属材料在承载时产生了各向异性强化的特点,因此,对这一类材料特性的深入研究显得十分必要,正确建立及分析理论模型将对在实际工程中的应用提供很好的理论依据。本文在R.Hill屈服准则下提出了无量纲化的解析应力解,讨论了屈服参数2>h时,正交异性材料平面应力问题的应力场及应力特征场,利用应力微分平衡方程得到了决定特征曲线特征的参数。结果说明特征线一般互不正交。特别地分析了平头冲压边界附近的情况,得到了各应力状态不同区域的应力特征场,应用数值分析的方法对过渡区进行了计算。